Thursday, June 16, 2011

Tutorial: Snappy Baby Romper (Pattern)

I love this little number.  I'd also be lying if it wasn't inspired a bit by the Snappy Toddler Top from Prudent Baby, which is also one of my favorites.  Though, with this i made a thicker neckline yoke, which i prefer the look of, but seriously, who wouldn't love a baby in this outfit!!!

To make this, I used an old sheet I had, which I love, i've used it for other projects, and have a lot left still!
  • You'll need :
    • the Pattern- at 100% (or no scaling) it's approximately 12-18m. For largerjust add legnth. For smaller. i would probably print it at 90% for 6m, 85% for 3m. 
      • i made it for my tall and skinny 8.5mo, who wears 6 or 9m body suits, 12m pants  (because of the length).
    • approximately 3/4 yards of a fabric
    • about 20in of elastic
    • 7 sets of snaps.
  1. using the front body piece, fold the middle with wrong sides together and match up the pleat lines, do a few stitches to tack this pleat. Then do the same with the two outer pleat markings on each side, this time folding and matching up the pleat lines with right sides together. Your front top will look like this.
  2. split center with the center front pleat loop and pin.
  3. Fold the outer pleat loops toward the middle, pin
  4. Using the back body piece, both back pleats will be done the same, fold and meet pleat lines with right sides together. Do a few stitches to tack the pleat. Fold the pleat loops toward the center of the body piece, pin.
  5. On both front and back body pieces, baste across the top at a 1/8th inch seam allowance to fix the pleats in place.
  6. For the front and back yoke pieces, there are 2 different ways you can complete the circular necks for both the first step is the same; starting at the markings, back stitch and stitch towards the outside of the yoke, around the top and finish (with a back stitch) at the other mark. The first way, you can clip the curves, flip it and fold/iron under the edges. The other way would be to complete it the same way that in the previous post, basting across most of the opening, clipping the curves, turning and ironing. Then seam ripping the basting edge, leaving a neatly folded over edge. Do this for both the front and back yoke pieces.
  7. Taking both front and back body pieces, stitch them together on both the sides at a 3/8th inch seam.
  8. Fold and iron the seam flat- for this I usually use my handy dandy flat iron that I’m too lazy to use on my hair.
  9. Hem the leg bottoms by folding it 1/4inch and iron; then 1 inch and iron. Make one row of stitches just under the hem amount. About 7/8 inch seam allowance, then again at 1/2inch seam allowance from the bottom, under it.
  10. Measure around the baby thigh to get the length of elastic needed per leg hole. Using a safety-pin lace the elastic through the casing we just made, tacking it down at each opening.
  11. To finish off the arm holes, apply bias tape around the edge, I usually prefer home made, since it’s A LOT cheaper and comes in prettier colors when you get to choose it. But I had a little left over bought stuff, so I just used that instead. Visit Dana Made It Blog for a tutorial on making and sewing bias tape.
  12. To apply the yoke to the body pieces, insert the body piece into the appropriate yoke open that we seam ripped. (front with front, back with back). Make sure there is about 1/2inch of the body piece inside the yoke.
  13. Pin.Stitch across the opening to finish the top at approximately a 1/8inch seam allowance. Stitch around the entire yoke at this seam allowance. Do the same for both front and back yoke pieces
  14. To finish the bottom of the romper, use inseam lining pieces. Take two of the pieces and line up. Stitch around the edges at 1/2inch seam allowance.
  15. Clip the curve. (for this, I much prefer using my pinking shears, cutting close to the line of stitches. It provides a quick and uniform clipping).
  16. Flip it inside out and iron. Do the same at the previous 2 steps for the remaining two inseam lining pieces.
  17. Line up the inseam lining pieces with the unfinished bottom seam, there will be hang over on each side. The pieces should be lined up on the right side of the fabric. Pin.
  18. Stitch the inseam at 1/4inch seam allowance. Clip the curve.
  19. Flip the lining to the inside of the body piece. Iron and stitch at 1/2inch seam allowance.
  20. Apply snaps to the inseam area.
  21. Apply snaps to each of the shoulders. And we’re done!!!

Here are a few action shots of mine on Baby:


Saturday, June 4, 2011

Rompers For Baby N

Baby M has been up to a lot lately. She’s recently learned how to crawl, but before she had the patience to do that, she decided to try out standing. She can’t figure out how to get there, so sometime she pushes up then just crawls around like this. Its hilarious.

And before I get to some of my new projects I’ve made, I just have to have a photo brag about my adorable child. I can’t believe she’s getting so big!!


Any who: on memorial day, my sister-in-law, Vanessa, was having a picnic/party. This was only the 3rd time I got to see my niece. So I just HAD to make her some delightful little summer outfits. (also adding them to my catalog of items that can be ordered through me!!!) Rompers are my Favorites!!! They’re seriously adorable, especially these ones, they’re based off of a few patterns that I had seen in Joann’s- New Looks 6970- and New Looks 6794. Both adorable patterns, but I am way too cheap to purchase those patterns, since they never go on sale. They are very simple patterns to fake too. Just simple pattern pieces I’ve made for other patterns, interchanged with other to make cute outfits. I have made a few cute rompers out of these ideas. Here are some of them I had made to hold you over until our next installment, I have an adorable romper pattern for you all!! Cheers!